无法从文档中提取型号,请重试

Update your browser

Your browser (Internet Explorer) is out of date.

Update your browser for more security, comfort and the best experience for this site.

首页 > 电子元器件选型 > 晶体管 > 小信号双极晶体管

MMBTA06

加入BOM

MMBTA06
已加入BOM:

Small Signal Bipolar Transistor, 0.5A I(C), 1-Element, NPN, Silicon, SOT-23, 3 PIN

市场均价:
¥0.3666
市场总库存:
-
生命周期状态: Contact Manufacturer
技术详情
价格 & 库存
替代料

文档下载

MMBTA06 Fairchild Semiconductor Corporation 也适用于 MMBTA06 MMBTA06 ON Semiconductor 也适用于 MMBTA06 ,PZTA06 SMBTA06 Infineon Technologies AG 也适用于 SMBTA06E6327XT ,MMBTA06 ,SMBTA06 等其余3个型号 MMBTA06WT1 ON Semiconductor 也适用于 MMBTA06WT1G ,MMBTA06WT1 ,SMMBTA06WT1G 等其余1个型号 MMBTA06L ON Semiconductor 也适用于 NSVMMBTA05LT1G ,MMBTA05L ,SMMBTA06LT1G 等其余7个型号 SMBTA06 Infineon Technologies AG 也适用于 MMBTA06LT1HTSA1 ,SMBTA06 ,SMBTA06E6327HTSA1

参考设计

(12)
Continuous Flyback for Voice over IP (VoIP) ringer (120V @ 40mA) - PMP1511.2 - TI Tool Folder
PMP1511: PMP1511 is a continous flyback circuit using the UCC2809. The input is 12V to 16.5V. The design provides two isolated outputs: 120V @ 40mA and 48V @ 30mA. The 120V output is regulated using opto feedback. The 48V is regulated through the coupling.
48Vdc Input, dual output (8V @ 0.25A) Isolated Flyback
PMP5847.2: This reference design uses the TPS40210 current mode controller to generate an isolated 6V/0.25A output and a non-isolated 8V/0.25A output over an input voltage rage of 40V - 60V DC. Isolation is achieved without the use of an optocoupler.
Wide Input Voltage Range Automotive Cuk LED Driver Reference Design (35V @ 0.75A)
PMP6012: PMP6012 reference design presents the TPS92690Q1 DC-DC controller driving a 18V to 35V string of LEDs at 750mA of current in a Cuk configuration. The Cuk topology features continuous input and output currents which helps reduce EMI and also allows one end of the LED string to connect to common ground allowing for a single wire system.
Reference Design - Two Switch Buck Boost Built with a Buck Controller
PMP7156: This reference design provides a solution to how to build a two switch Buck Boost Converter with a Buck Controller for small loads. An input voltage between 8V and 16V is converted to 12V at the output with a 1A load.
9Vdc-57Vdc Input, 56V/20W Isolated Flyback
PMP6963: This reference design uses the TPS40210 current mode controller to generate an isolated 56V/0.35A output from a wide 9V - 57V DC input. This design uses diode rectification on the output stage and achieves efficiencies up to 89% at full load with peaks over 90%.
Continuous Flyback for Voice over IP (VoIP) ringer (120V @ 40mA)
PMP1511.2: PMP1511 is a continous flyback circuit using the UCC2809. The input is 12V to 16.5V. The design provides two isolated outputs: 120V @ 40mA and 48V @ 30mA. The 120V output is regulated using opto feedback. The 48V is regulated through the coupling.
Continuous Flyback for Voice over IP (VoIP) ringer (48V @ 30mA)
PMP1511.1: PMP1511 is a continous flyback circuit using the UCC2809. The input is 12V to 16.5V. The design provides two isolated outputs: 120V @ 40mA and 48V @ 30mA. The 120V output is regulated using opto feedback. The 48V is regulated through the coupling.
Isolated discontinuous mode isolated flyback 3.3V @ 1.5A
PMP6516: This compact and low-cost (5W) isolated flyback regulator produces a 3.3V output from a 48V input, such as Telecom. A full-load efficiency of 82% was achieved from a 48V nominal input.
Isolated DM Flyback 6.5V@1A
PMP6606: This low-cost (6.5W) isolated synchronous discontinuous flyback regulator produces a 6.5V output from a low-voltage (18V – 36V) input. A full-load efficiency of nearly 90% was achieved from a 24V nominal input.
Class 4- 33Vdc-57Vdc Input, 12V/2.1A Active Clamp Forward
PMP4909: The PMP4909 reference design uses the TPS23754 PoE controller to control an active clamp forward converter that delivers up to 25W at 12V. This design uses synchronous rectifiers to achieve efficiencies over 92%.
48Vdc Input, dual output (6V @ 0.25A) Isolated Flyback
PMP5847.1: This reference design uses the TPS40210 current mode controller to generate an isolated 6V/0.25A output and a non-isolated 8V/0.25A output over an input voltage rage of 40V - 60V DC. Isolation is achieved without the use of an optocoupler.
显示更多价格 & 库存吗?

价格走势

库存走势

No Data Available
显示更多替代料吗?
新建BOM