参考设计
(50)
Quad Isolated Outputs Fly-Buck Bias Supply for IGBT Gate Driver Reference Design
PMP9460.2: The PMP9460 reference design is a quad isolated output Fly-Buck power supply designed for IGBT gate driver bias in motor drive or inverter applications. It features the LM5017, 7.5-100V wide Vin, 600mA, Constant On-Time (COT), synchronous buck regulator configured in the Fly-Buck topology. The Fly-Buck converter is a simple, cost effective and compact isolated power solution. The reference board generates two pair of +16V and -9V outputs each with 100mA current capability; they are suitable for biasing the gate drivers of two IGBTs. The supply provides good regulation performance over an input voltage range of 19V to 30V.
LM5017 Flybuck Quad Isolated Output Power Supply without Opto-coupler - PMP7993.2 - TI Tool Folder
PMP7993: This Flybuck reference design uses the LM5017 buck regulator to generate four isolated outputs: ±15V@50mA and ±5V@100mA. The regulation is done on the primary side, and thus no opto-coupler is needed. The overall load/line regulation for each output is within +/-5%. The input voltage range is from 17V to 32V. It's suitable for applications requiring multiple positive and negative bias voltage rails.
Flybuck Power Supply Using LM5017, Two 12V@0.25A Outputs
PMP7941.2: This reference design uses the LM5017 Flybuck regulator to generate two 12V output at 250mA. One output is at the primary side and the other is on the isolated secondary side. By reverse the output and ground connection of the secondary side, the isolated output becomes -12V. It's suitable for applications requiring +/-12V bias powers. The input range is from 17V to 32V.
Ultrasonic Distance Measurement BoosterPack Reference Design
TIDA-00462: The TIDA-00462 ultrasonic distance measurement reference design can measure the distance up to 99 inches with an accuracy of ±1.5 inches. The scope of this design guide is to give system designers a head-start in integrating TI’s industrial ultra-low-power MCU, analog signal conditioning, and power management technologies into their end-equipment systems. This design guide describes the principle of operation and basic design process for a low cost distance measuring system based on ultrasonic sound utilizing the MSP430 ultralow-power microcontroller. This design guide also addresses component selection, design theory, and test results of the TI Design system. All the relevant design files like Schematics, BOM, Layer plots, Altium files, Gerber and MSP430 MCU firmware are provided.
Isolated Bias Supplies + Isolated Amplifier Combo for Line Voltage or Current Measurement
PMP9480: PMP9480 is a dual output Flybuck Converter plus an Isolated amplifier combo solution that can not only be used for sensing Line voltage or Line current but also provide Aux Bias power for complete Industrial system . The design accepts very Wide input voltage of 10 Vin to 72Vin DC(Work on any Batteries such as 12V/24V or 48V or any available Industrial DC bus ) and provides Isolated outputs of 5V@350mA(Primary Bias Supply for Controller , Amplifiers ,Interfaces, etc ) and 5V@150mA(Secondary Isolated Bias for Isolated Amplifiers , Isolated communication etc ) . It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters . Isolated Amplifier AMC1200 used in this design is a precision isolation amplifier with an output separated from the input circuitry by a silicon dioxide (SiO2) barrier that is highly resistant to magnetic interference.
Low-Power Isolated Supply, Input range: 36V to 75V, Output: 10V @ 120mA, LM5017
PMP7798.3: An isolated bias supply is implemented in this evaluation board with LM5017 Constant-On-Time regulator using a coupled inductor. LM5017 regulator integrates both the high and low side power switches essential for creating isolated converter. The input voltage range is 36V to 75V and it drives an output of 10V @ 120mA.
Flybuck Dual Isolated Power Supply without Opto, 17 - 32V input, Dual 12V @ 0.25A output
PMP7941.1: This reference design uses the LM5017 Flybuck regulator to generate two 12V output at 250mA. One output is at the primary side and the other is on the isolated secondary side. By reverse the output and ground connection of the secondary side, the isolated output becomes -12V. It's suitable for applications requiring +/-12V bias powers. The input range is from 17V to 32V.
System on Module for G3-PLC Power Line Communication (CENELEC frequency band)
TIDM-SOMPLC-G3-CENELEC: The SOMPLC-F28PLC83 is a single-board System on Module(SOM) for G3-PLC in the CENELEC frequency band. Texas Instruments’ production-ready G3-PLC software is available along with the SOMPLC-F28PLC83. Engineers can take the SOM design and integrate it into their overall system board or keep the design as an add-on board to their application. The only additional hardware required is the AC mains line coupling circuitry. The included hardware schematics and Gerber files simplify the task for engineers to add PLC to their end system. OEMs will benefit from having the ability to rapidly evaluate and prototype Power Line Communications technology in their application.
Power Solution for an Automotive Voltage Quality Module
PMP7916: The PMP7916 is a boost converter that can be used by a voltage quality module in a start-stop car to condition the battery voltage seen by electronic loads. For such a car to utilize existing electronic assemblies, input voltage to the assemblies is not allowed to dip to 6V during warm cranking or else they will momentarily shut down. The PMP7916 keeps the input voltage above 10.5V during cranking, and bypasses the battery voltage when it goes above 12V. When boosting a low battery voltage during cranking, the PMP7916 can support a 500W load for 5 seconds.
Quad Isolated Outputs Fly-Buck Bias Supply for IGBT Gate Driver Reference Design
PMP9460.1: The PMP9460 reference design is a quad isolated output Fly-Buck power supply designed for IGBT gate driver bias in motor drive or inverter applications. It features the LM5017, 7.5-100V wide Vin, 600mA, Constant On-Time (COT), synchronous buck regulator configured in the Fly-Buck topology. The Fly-Buck converter is a simple, cost effective and compact isolated power solution. The reference board generates two pair of +16V and -9V outputs each with 100mA current capability; they are suitable for biasing the gate drivers of two IGBTs. The supply provides good regulation performance over an input voltage range of 19V to 30V.
Quad Isolated Outputs Fly-Buck Bias Supply for IGBT Gate Driver Reference Design
PMP9460.4: The PMP9460 reference design is a quad isolated output Fly-Buck power supply designed for IGBT gate driver bias in motor drive or inverter applications. It features the LM5017, 7.5-100V wide Vin, 600mA, Constant On-Time (COT), synchronous buck regulator configured in the Fly-Buck topology. The Fly-Buck converter is a simple, cost effective and compact isolated power solution. The reference board generates two pair of +16V and -9V outputs each with 100mA current capability; they are suitable for biasing the gate drivers of two IGBTs. The supply provides good regulation performance over an input voltage range of 19V to 30V.
Low-Power Isolated Supply, Input range: 36V to 75V, Output: 5V @ 80mA, LM5017
PMP7798.2: An isolated bias supply is implemented in this evaluation board with LM5017 Constant-On-Time regulator using a coupled inductor. LM5017 regulator integrates both the high and low side power switches essential for creating isolated converter. The input voltage range is 36V to 75V and it drives an output of 5V @ 80mA.
Low Profile Quad Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design
PMP9478: The PMP9478 reference design is a low profile quad output isolated Flybuck power supply for industrial applications. The power supply has a synchronous buck regulator, LM5017, and a low profile (6mm) transformer. It generates four isolated outputs of ±5V, ±15V, 50mA each. The LM5017 is a 100V wide Vin, 600mA synchronous buck regulator. The input voltage range of the design is 20V to 32V, making it suitable for 24V input industrial application. The Flybuck can regulate the secondary side outputs without opto-coupler or aux winding, and is capable of achieving good cross regulation within ±5%. With LM5017's Constant On-Time control, no loop compensation is required, which simplifies the design and helps reduce the external part count and BOM cost.
Low Profile Quad Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design
PMP9478.3: The PMP9478 reference design is a low profile quad output isolated Flybuck power supply for industrial applications. The power supply has a synchronous buck regulator, LM5017, and a low profile (6mm) transformer. It generates four isolated outputs of ±5V, ±15V, 50mA each. The LM5017 is a 100V wide Vin, 600mA synchronous buck regulator. The input voltage range of the design is 20V to 32V, making it suitable for 24V input industrial application. The Flybuck can regulate the secondary side outputs without opto-coupler or aux winding, and is capable of achieving good cross regulation within ±5%. With LM5017's Constant On-Time control, no loop compensation is required, which simplifies the design and helps reduce the external part count and BOM cost.
7V to 40V Wide Input, 3-Output SIMPLE SWITCHER® Reference Design Using LMR14050 and LMZ20502
PMP10743.1: The reference design shows the wide input voltage capability, simple layout, and small solution size of the LMR14050 SIMPLE SWITCHER® Buck Converter and the LMZ20502 Nano Module. The LMR14050 provides a 5V output rail which feeds into two LMZ20502 Nano Modules. The modules provide a 3.3V and a 1.8V rail. The 5V, the 3.3V, and the 1.8V rails are capable of delivering a maximum of 2A load at their respective output voltages.
192W Dual-Phase Synchronous Boost Converter Reference Design
PMP9403: PMP9403 is a high-efficiency dual-phase synchronous boost converter using the LM5122 controller ICs. The design accepts an input voltage of 9Vin to 15Vin (12Vin Nominal) and provides an output of 48Vout capable of supplying 4A of continuous current to the load.
Wide VIN FlyBuck™ Power Converter with Two Isolated Bias Supplies + One Non-Isolated Power
PMP7798.1: Based on the Wide VIN COT Sync Buck regulator LM5017, this FlyBuck circuit provides excellent regulation for two isolated outputs and one non-isolated output. Compared with a conventional Flyback circuit, this design features a smaller board size and minimized BOM without the need for an optocoupler. This design is well suited for applications which need bias power. Additional output voltage versions of this board are available: see PMP7798.2 and PMP7798.3
7V to 40V Wide Input, 3-Output SIMPLE SWITCHER® Reference Design Using LMR14050 and LMZ20502
PMP10743.2: The reference design shows the wide input voltage capability, simple layout, and small solution size of the LMR14050 SIMPLE SWITCHER® Buck Converter and the LMZ20502 Nano Module. The LMR14050 provides a 5V output rail which feeds into two LMZ20502 Nano Modules. The modules provide a 3.3V and a 1.8V rail. The 5V, the 3.3V, and the 1.8V rails are capable of delivering a maximum of 2A load at their respective output voltages.
Interface to a Sin/Cos Encoder with Sitara AM437x Reference Design
TIDA-00178: The TIDA-00178 reference design is an EMC compliant industrial interface to Sin/Cos position encoders. Applications include industrial drives, which require accurate speed and position control. The design utilizes a 16-bit dual sample ADC with drop-in compatible 14- or 12-bit versions available, allowing for optimization of performance and cost. TIDA-00178 provides a direct connection to Sitara AM437x using SPI and QEP. For quick evaluation it features a 60-pin connector which directly fits the AM437x IDK. An example firmware for Sitara AM437x IDK is provided, which outputs the measured angle from the Sin/Cos encoder with up to 28-bit resolution through the Sitara’s USB virtual COM port.
Reference Design - MOSFET Driver for Half Bridge with a Fly-Buck to Provide Isolated Power
PMP10645: The PMP10645 reference design is designed for SM74101 mosfet driver with a Fly-Buck power supply to drive half bridge. The SM74101 is a tiny 7A mosfet driver which can support 3A source current and 7A sink current. The LM5017 isolated output Fly-Buck power supply has four outputs to supply the gate driver bias in motor drive or inverter applications. The user can also use jumpers to set Unipolar or Bipolar PWM gate driver.
Direct Type/ Local Dimming (Conventional TV power + Boost + LED driver)
PMP4298: In this topology, the UCC28051 is a boost transition mode (TM) power factor corrector (PFC), which can rectify an AC input line voltage to 380V DC; the resonant LLC stage UCC25600 regulates the output to 24V/2A for an audio amplifier with feedback to the LLC controller, and 48V for the LED driver input. The flyback with UCC28610 in parallel generates 5V/3A for the system board and 5V/1A for standby power. In the LED driver stage, the 48V input voltage requires another front end boost stage to boost the output voltage to 80V, which connects to the eight-channel TLC5960 with 20LEDs at 120mA per string.This technique is the most common type of current LED backlight; the LLC design is easily implemented. The intelligent headroom voltage monitor (oriHVM™) automatically minimizes the power loss caused by the LED forward voltage change. Only a single additional resistor regulates the boost dc-dc output voltage.
Reference Design - MOSFET Driver for Half Bridge with a Fly-Buck to Provide Isolated Power
PMP10645.1: The PMP10645 reference design is designed for SM74101 mosfet driver with a Fly-Buck power supply to drive half bridge. The SM74101 is a tiny 7A mosfet driver which can support 3A source current and 7A sink current. The LM5017 isolated output Fly-Buck power supply has four outputs to supply the gate driver bias in motor drive or inverter applications. The user can also use jumpers to set Unipolar or Bipolar PWM gate driver.
Quad Isolated Outputs Fly-Buck Bias Supply for IGBT Gate Driver Reference Design
PMP9460.3: The PMP9460 reference design is a quad isolated output Fly-Buck power supply designed for IGBT gate driver bias in motor drive or inverter applications. It features the LM5017, 7.5-100V wide Vin, 600mA, Constant On-Time (COT), synchronous buck regulator configured in the Fly-Buck topology. The Fly-Buck converter is a simple, cost effective and compact isolated power solution. The reference board generates two pair of +16V and -9V outputs each with 100mA current capability; they are suitable for biasing the gate drivers of two IGBTs. The supply provides good regulation performance over an input voltage range of 19V to 30V.
LM5017 Flybuck Quad Isolated Output Power Supply without Opto-coupler
PMP7993.3: This Flybuck reference design uses the LM5017 buck regulator to generate four isolated outputs: ±15V@50mA and ±5V@100mA. The regulation is done on the primary side, and thus no opto-coupler is needed. The overall load/line regulation for each output is within +/-5%. The input voltage range is from 17V to 32V. It's suitable for applications requiring multiple positive and negative bias voltage rails.
Powering PLC I/O Module with LM5017 Flybuck Reference Design
PMP7993.1: The LM5017 Flybuck reference design provides multiple isolated outputs to supply the bias voltage needed in a PLC I/O module. It generates 4 isolated outputs: ±15V@50mA and ±5V@100mA; it can cover most of the required voltage rails in the I/O module, such as the OP-AMP, DAC bias, RS-485 transmitter and digital isolator power supplies. In the Flybuck, the regulation is done on the primary side, and thus no opto-coupler is needed. The overall load/line regulation for each output is within +/-5%. The input voltage range is from 17V to 32V.
120Vac Single Stage Non-Dimmable 50W LED Driver Reference Design
PMP6017: This reference design provides a high power ( 50W ) non-isolated, non-dimming LED driver based on the TPS92074. With a nominal input of 120VAC and input range covering 108VAC to 132VAC, the design provides 1 Amp of output current to a 47V nominal stack of LEDs (~16 LEDs). The Buck PFC provides high power factor and low THD.
Power Solution for an Automotive Voltage Stabilizer
PMP7919: The PMP7919 is a 2-phase synchronous boost converter that can take a minimum 5.5V input and put out 11.5V or higher at 15A. It is used in the Voltage Quality Module in a start-stop vehicle where warm cranking is not allowed to cause certain electronic loads (such as the head unit) to power cycle. When the start-stop vehicle goes through warm cranking, the lead acid battery voltage may dip to 6V (in the US) momentarily. The PMP7919 boost converter will, in this case, immediately respond to the transient so that its output voltage will stay in specifications, preventing downstream electronic loads from shutting down. When the battery voltage is higher than the boost converter's output regulation point (typically 11.5V), the synchronous boost converter will operate in bypass mode and leave the high-side FETs on 100%, saving extra bypass FETs and a control circuit that would be required if a non-synchronous boost converter were to be used.
14-Channel Active Cell Balance Battery Management Reference Design
TIDA-00239: Active Balance chipset for use in large format Lithium-ion batteries that provides monitoring, balancing, and communications. With precise and robust active balancing, the Active Balance BMS is capable of bidirection power transfer at each cell. Each EM1401EVM can manage 6 to 14 cells (60V max) for Li-ion battery applications. The EM1401EVM modules can be stacked up to 1300V. The system provides fast cell balancing, diagnostics, and module to controller communication. Independent protection circuitry is also provided.
Quad Isolated Outputs Fly-Buck Bias Supply for IGBT Gate Driver Reference Design - PMP9460.2 - TI Tool Folder
PMP9460: The PMP9460 reference design is a quad isolated output Fly-Buck power supply designed for IGBT gate driver bias in motor drive or inverter applications. It features the LM5017, 7.5-100V wide Vin, 600mA, Constant On-Time (COT), synchronous buck regulator configured in the Fly-Buck topology. The Fly-Buck converter is a simple, cost effective and compact isolated power solution. The reference board generates two pair of +16V and -9V outputs each with 100mA current capability; they are suitable for biasing the gate drivers of two IGBTs. The supply provides good regulation performance over an input voltage range of 19V to 30V.
7V to 40V Wide Input, 3-Output SIMPLE SWITCHER® Reference Design Using LMR14050 and LMZ20502
PMP10743.3: The reference design shows the wide input voltage capability, simple layout, and small solution size of the LMR14050 SIMPLE SWITCHER® Buck Converter and the LMZ20502 Nano Module. The LMR14050 provides a 5V output rail which feeds into two LMZ20502 Nano Modules. The modules provide a 3.3V and a 1.8V rail. The 5V, the 3.3V, and the 1.8V rails are capable of delivering a maximum of 2A load at their respective output voltages.
Flybuck Power Supply Using LM5017, Two 12V@0.25A Outputs - PMP7941.2 - TI Tool Folder
PMP7941: This reference design uses the LM5017 Flybuck regulator to generate two 12V output at 250mA. One output is at the primary side and the other is on the isolated secondary side. By reverse the output and ground connection of the secondary side, the isolated output becomes -12V. It's suitable for applications requiring +/-12V bias powers. The input range is from 17V to 32V.
LM5017 Flybuck Quad Isolated Output Power Supply without Opto-coupler
PMP7993.2: This Flybuck reference design uses the LM5017 buck regulator to generate four isolated outputs: ±15V@50mA and ±5V@100mA. The regulation is done on the primary side, and thus no opto-coupler is needed. The overall load/line regulation for each output is within +/-5%. The input voltage range is from 17V to 32V. It's suitable for applications requiring multiple positive and negative bias voltage rails.
Low Profile Quad Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design
PMP9478.1: The PMP9478 reference design is a low profile quad output isolated Flybuck power supply for industrial applications. The power supply has a synchronous buck regulator, LM5017, and a low profile (6mm) transformer. It generates four isolated outputs of ±5V, ±15V, 50mA each. The LM5017 is a 100V wide Vin, 600mA synchronous buck regulator. The input voltage range of the design is 20V to 32V, making it suitable for 24V input industrial application. The Flybuck can regulate the secondary side outputs without opto-coupler or aux winding, and is capable of achieving good cross regulation within ±5%. With LM5017's Constant On-Time control, no loop compensation is required, which simplifies the design and helps reduce the external part count and BOM cost.
High Efficiency Isolated CAN & Profibus Interface Reference Design
TIDA-00012: The High Efficiency Isolated CAN & Profibus Interface Solution TI Design is intended for use in industrial systems that require isolated power for CAN and/or Profibus transceivers. This TI Design highlights the ability to completely shut off both the power converter and data transceivers with just one GPIO signal from a microcontroller (when dropping into low power modes, for example). This isolated interface solution delivers accurately regulated rails for both primary and secondary power to TI’s Profibus and CAN transceivers without costly opto-coupler feedback circuits – making this the simplest, most efficient and flexible isolated interface solution for industrial automation on the market today. Other solutions using transformer drivers are not efficient and do not have the ability to be easily turned off and require additional components to regulated the secondary rail. Lastly, this TI Design has the additional feature of allowing the MCU to wait until power is good before transmitting data or to stop transmitting data if a power fault has occured on the interface. The Tiva C Series Launch Pad form factor of this TI Design allows easy connection to the LaunchPad board for use of the Tiva C microcontroller in handling the communications protocol to the interface. The combination of the two boards provides a complete, low cost CAN and Profibus communication solution.
LM5017 Flybuck Quad Isolated Output Power Supply without Opto-coupler
PMP7993.4: This Flybuck reference design uses the LM5017 buck regulator to generate four isolated outputs: ±15V@50mA and ±5V@100mA. The regulation is done on the primary side, and thus no opto-coupler is needed. The overall load/line regulation for each output is within +/-5%. The input voltage range is from 17V to 32V. It's suitable for applications requiring multiple positive and negative bias voltage rails.
24Vin+/-10%, 5Vout @ 0.3A Flybuck Converter
PMP9362: An isolated flybuck converter with self-driven synchronous rectification on the secondary side accepts an input voltage of 21.6Vin to 26.4Vin and provides an isolated output of 5Vout capable of supplying a maximum of 0.3A of current to the load.
Low Profile Quad Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design - PMP9478.3 - TI Tool Folder
PMP9478: The PMP9478 reference design is a low profile quad output isolated Flybuck power supply for industrial applications. The power supply has a synchronous buck regulator, LM5017, and a low profile (6mm) transformer. It generates four isolated outputs of ±5V, ±15V, 50mA each. The LM5017 is a 100V wide Vin, 600mA synchronous buck regulator. The input voltage range of the design is 20V to 32V, making it suitable for 24V input industrial application. The Flybuck can regulate the secondary side outputs without opto-coupler or aux winding, and is capable of achieving good cross regulation within ±5%. With LM5017's Constant On-Time control, no loop compensation is required, which simplifies the design and helps reduce the external part count and BOM cost.
Quad Isolated Outputs Fly-Buck Bias Supply for IGBT Gate Driver Reference Design - PMP9460.3 - TI Tool Folder
PMP9460: The PMP9460 reference design is a quad isolated output Fly-Buck power supply designed for IGBT gate driver bias in motor drive or inverter applications. It features the LM5017, 7.5-100V wide Vin, 600mA, Constant On-Time (COT), synchronous buck regulator configured in the Fly-Buck topology. The Fly-Buck converter is a simple, cost effective and compact isolated power solution. The reference board generates two pair of +16V and -9V outputs each with 100mA current capability; they are suitable for biasing the gate drivers of two IGBTs. The supply provides good regulation performance over an input voltage range of 19V to 30V.
Low Profile Quad Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design
PMP9478.2: The PMP9478 reference design is a low profile quad output isolated Flybuck power supply for industrial applications. The power supply has a synchronous buck regulator, LM5017, and a low profile (6mm) transformer. It generates four isolated outputs of ±5V, ±15V, 50mA each. The LM5017 is a 100V wide Vin, 600mA synchronous buck regulator. The input voltage range of the design is 20V to 32V, making it suitable for 24V input industrial application. The Flybuck can regulate the secondary side outputs without opto-coupler or aux winding, and is capable of achieving good cross regulation within ±5%. With LM5017's Constant On-Time control, no loop compensation is required, which simplifies the design and helps reduce the external part count and BOM cost.
Cascaded LMH5401 and LMH6401 Reference Design
TIDA-00654: A wideband single-ended to differential conversion reference design in both DC- and AC- coupled applications is presented. The design evaluates the performance of the LMH5401 and LMH6401 cascade and offers insight into the design.
